Skip to content
Rancho Palos Verdes, CAMon–Sat 7AM–7PM · Sun 8AM–5PM
(310) 555-0123
(310) 555-0123
Heating & air conditioning service

Furnace Repair in Lomita, CA

Furnace and heating repair covering ignition faults, flame sensors, limit switches, control boards, blower motors and gas valves, with a combustion and venting safety check on every visit.

  • Starts at $89, with the full price in writing first
  • Before and after photos of the work
Call (310) 555-0123All of Palos Verdes

Get Your Free Quote

Tell us what the house is doing. We reply during business hours with a range and a time window.

No obligation · nothing starts before you have a written price

Direct answer · pricing

Furnace Repair in Lomita starts at $89. Nothing is added for travel inside Lomita, and the written figure is fixed from the moment you have it. Ring (310) 555-0123 for yours.

Heating Diagnostic VisitFull ignition sequence plus a combustion and venting check. Priced identically in the 250th Street area and the Railroad Museum blocks.
From $89
Flame Sensor Clean or ReplacementThe most common cause of a furnace that lights then quits
From $149
Hot Surface Igniter ReplacementPart matched to the furnace, not a universal substitute. The same rate citywide.
From $239
Pressure Switch or Limit SwitchWith the airflow cause checked, not just the switch replaced
From $279
Blower Motor or Control BoardPart and labour, quoted before the work starts. On the written quote before we start.
From $579
Gas Valve or Heat Exchanger FindingQuoted in writing with a replacement comparison
Quoted

Furnace Repair for Lomita Homeowners

Most of the furnaces in Lomita are larger than the house needs, because they were sized for a draughtier version of it decades ago. Small forced-air units and the occasional wall furnace, often serving a floor area that has grown since the system was installed, and the result is uneven comfort and more wear than the equipment should be taking. Lomita is a two-square-mile city wedged between the peninsula and the harbor, with a small-town street grid, a legacy of horse keeping on a few of the older lots, and housing that ranges from modest 1950s bungalows to small multi-unit buildings and a growing number of accessory dwellings in back yards.

We watch a full ignition cycle from the thermostat call and note exactly where it stops, which identifies the component rather than guessing at it. Then the things that cause repeat failures — filter, static pressure, limit history, condensate trap and gas pressure — followed by the safety set: flue and vent connector, draft, the accessible heat exchanger and a carbon monoxide reading in the supply air. In Lomita, small forced-air units and the occasional wall furnace, often serving a floor area that has grown since the system was installed, which is exactly why that safety pass matters.

Signs You Need Furnace Repair in Lomita

The furnace lights and then shuts down after a few seconds, repeatedly
The thermostat calls for heat and nothing happens at all, a regular call through the Pennsylvania Avenue blocks and the 250th Street area
Air from the registers is cool while the furnace is running
A rumbling, booming or scraping noise at startup, routine on jobs around here
A burning or sooty smell, or visible soot near the furnace or vents
A carbon monoxide alarm has sounded, or the pilot or burner flame is yellow rather than blue, which we see often in the Narbonne Avenue corridor

How Furnace Repair Works in Lomita

The steps below do not get shortened because a schedule is tight. This is what furnace repair involves, every time.

  1. Watch a full cycleWe run the furnace from a thermostat call and note exactly where in the ignition sequence it fails. Handled identically near the Railroad Museum.
  2. Check airflow and filterStatic pressure, filter and blower condition, because a furnace that overheats is usually a furnace that cannot breathe.
  3. Measure electrically and at the gas valveIgniter, sensor, switches, board voltages and gas pressure measured against specification and photographed.
  4. Combustion and venting safety checkFlue, vent connector, draft, accessible heat exchanger and a carbon monoxide reading in the supply air. Never skipped, whatever the schedule looks like.
  5. Written price, then the repairYou see the readings, the photos and a written price, with a replacement comparison on any large repair.

What We See in Lomita Neighborhoods

A heat pump is now a real option rather than a novelty in this climate, and on a the Railroad Museum blocks job we will price it alongside a like-for-like furnace if the panel and the ducts can take it. If they cannot, we say so instead of selling the idea.

Added living space is the recurring theme. When a garage becomes a bedroom or a back-yard unit goes in, the heating, cooling and laundry venting usually get extended rather than redesigned: a branch tapped into an existing trunk, a flexible duct run on the floor of a crawlspace, a dryer vented into a soffit. None of that is unfixable, but it does mean we ask what was built and when before we quote.

Side-yard clearance matters more on small lots than anyone expects. A condenser with a fence eighteen inches from the coil recirculates its own hot air and loses capacity on exactly the days you need it, and no amount of refrigerant fixes that. Sometimes the fix is a service clearance and a cleaned coil rather than a new unit, and we would rather tell you that.

No travel charge inside Lomita, no scripts, and nothing invented. Anything we recommend is photographed first so you are looking at the same evidence we are. Reach us on (310) 555-0123.

Frequently Asked Questions

How much does furnace repair cost?
The diagnostic visit is $89, credited against the repair if you proceed the same day. A flame sensor or igniter is typically $150 to $250; a blower motor or control board runs higher. Call (310) 555-0123 for a quote.
Why does my furnace start then shut off after a few seconds?
That pattern is usually a dirty or failing flame sensor: the burner lights, the furnace cannot confirm the flame and it shuts the gas off as designed. It is an inexpensive repair and the symptom is very recognisable.
Do you check for carbon monoxide?
Yes. Every heating visit includes a look at the flue and vent connector, a draft check, an inspection of the accessible heat exchanger and a carbon monoxide reading in the supply air. California also requires CO alarms in homes with fuel-burning appliances.
Is a cracked heat exchanger repairable?
No. A cracked heat exchanger means the furnace is finished, and the appliance should be shut down rather than run. We photograph the crack and show you before recommending anything.
Do you provide furnace repair near the Railroad Museum?
Yes. Furnace repair is available across Lomita, including the Pennsylvania Avenue blocks, the 250th Street area, and the Railroad Museum blocks, with no travel fee within the city. Call (310) 555-0123 or send the form.
Where can I find furnace repair near me in Lomita?
Right here — we work Lomita week in, week out from a base in Rancho Palos Verdes, roughly 5 miles out. Most bookings land within a day or two with a confirmed window.

Nearby Cities We Cover

Listed by actual distance from this page, nearest first.

Furnace Repair in Harbor City1.1 miles awayFurnace Repair in Rolling Hills Estates2.5 miles awayFurnace Repair in Wilmington3.1 miles awayFurnace Repair in Carson3.3 miles awayFurnace Repair in Torrance3.3 miles awayFurnace Repair in Rolling Hills3.4 miles away

More nearby: Chimney Sweep · Chimney Repair · Air Duct Cleaning · Dryer Vent Cleaning · AC Repair · All Lomita services

Furnace Repair in Lomita, Booked by Phone

Call now, or send the form above and we will confirm a window that works for your address.

Call (310) 555-0123Send the Details
(310) 555-0123
Call NowFree Quote